vibration screen

vibration sieve is one of precise powder sieve with low noise and high efficiency. It needs only 3-5 minute to replace the scree

MODEL	POWER(KW)	SIEVE DIAMETER	CUBIC METERS	SIEVE LAYER
1S HC-450- 2S 3S	0.18	Φ320mm	580×580×560 580×580×660 580×580×760	1 2 3
1S HC-600- 2S 3S	0.55	Φ550mm	800×800×680 800×800×780 800×800×880	1 2 3
1S HC-800- 2S 3S	0.75	Φ750mm	900×900×780 900×900×930 900×900×1080	1 2 3
1S HC-1000- 2S 3S	1.1	Φ950mm	1160×1160×880 1160×1160×1030 1160×1160×1180	1 2 3
1S HC-1200- 2S 3S	1.47	Φ1150mm	1360×1360×980 1360×1360×1160 1360×1360×1360	1 2 3
1S HC-1500- 2S 3S	2.2	Φ1450mm	1850×1850×1130 1850×1850×1330 1850×1850×1550	1 2 3
1S HC-1800- 2S 3S	2.2	Φ1750mm	2200×2200×1360 2200×2200×1460 2200×2200×1680	1 2 3

A.            Vibrating screen

XDVS series vibrating sieve is one of precise powder sieve with low noise and high

efficiency. It needs only 4-6 minutes to replace the screen rapidly, all closed structure.

It was used to filter particles, powder and mucila.

B.            Principle of the structure:

XDVS series vibrating sieve uses upright motor as the source of vibration, equipped

eccentricity hammer on the both sides of motor, changed circumrotate to level, upright and

incline movement, then pass these three movements to the surface of the screen. Adjust the

phase angle on the both sides of the top and bottom changing the movement orbits in the

surface screen.

C.              Features:

1) High efficiency, refined design, duration, any powders and mucilage are suitable for

using.2) Easily replace the screen, simple operation and convenience washing. 3) Never jam the mesh with no powder flying and filter size of the powder between 0.025mm

and 0.029mm. 4) Discharge the impurity and coarse materials automobile and operates continuously. 5) Small volume, move easily. 6) The highest layers of the screen are about 5 layers. But 3 layers are suggested.

D.              Installation and adjustment

 1, the motor should be fastened on the mounting surface, mounting surface must be smooth,

flat.  2, the motor can be installed horizontally.  3, the electrical lead-core rubber cable with four-YZ-500V, then the power cable is not

allowed when there is acute Lead off, and with the vibration of the body and firmly

secured.  4, electrical grounding should be reliable, the motor grounding device, lead terminal

signs, can also use foot bolts solid ground.   5, the exciting force adjustments.   

E.              Use and maintenance

1, the machine shall be equipped with electrical protection device. 2, the machine is running early, check every day at least once a bolt to prevent

loosening. 3, when the motor direction of rotation does not meet the requirements, you can adjust the

power supply phase sequence.  4, the motor should guarantee good lubrication, each running about two weeks to add

lithium grease (ZL-3) once, come on, through the oil by adding appropriate amount of

lithium grease cup.   5, the machine running total of 1500 hours, check the bearings, if serious injury should

be immediately replaced.  6, the machine parked or garaged when used again after a long time, measure the

insulation resistance should be used to measure 500-volt megger.

vibration screen